Pipe와 Flange(플렌지) 규격자료
|
|
Pipe와 Flange 규격에 대한 자료입니다.
1. KS, JIS 배관규격
2. ASME 배관규격
3. ANSI 150#,300# FLANGE 규격
4. ANSI 600#,900# FLANGE 규격
5. 1500# FLANGE 규격
6. KS,JIS FLANGE 규격
7. API 규격
8. DIN 규격
9. FLANGE 중량표(150#,300#,600#,900#)
규격에 대한 기초는 아래와 같습니다.
Slip On Flange - 슬립온 타입 플랜지
FF - Flat face 타입의 플랜지 면
DN 15 - 구경이 15mm
CS - Carbon Steel 재질이 카본스틸
JIS 5K - CODE가 JIS
SUS - 재질이 SUS 316
SCH - 스캐쥴 / 배관의 두께를 말합니다.
LR - Long Radius 반경이 구경의 1.5배
SR - Short Radius 반경이 구경의 1.0배
'Design > Piping' 카테고리의 다른 글
스팀 트레이싱, 증기 트레이싱, Steam tracing (0) | 2013.09.11 |
---|---|
ASME B16.5 Flange rating (플랜지 레이팅) 자동 계산 (0) | 2013.04.29 |
각 밸브별 특성과 장단점 (0) | 2013.03.05 |
플랜지 레이팅 계산기 - Flange Rating Calculator (NPS 0.5 to 60) (0) | 2013.02.26 |
개스킷 재질 (Gasket Materials) (0) | 2013.02.26 |
플러그 이음 ( Bell and Spigot Joint )
|
|
플러그 이음 ( Bell and Spigot Joint )
내경을 상대 관 끝의 외경에 맞춰서 연결하는 파이프 이음을 말한다. 동관과 경질 염화비닐관 등에 이용된다. 전자는 납땜으로, 후자는 접착제 또는 가열에 의해 접합된다. 일반적인 관이음과 같이 여러 가지 모양이 있다.
하수처리에는 플러그 이음이 많이 이용되며, 아래는 표준 치수이다.
'Design > Piping' 카테고리의 다른 글
Pipe와 Flange(플렌지) 규격자료 (0) | 2013.03.22 |
---|---|
각 밸브별 특성과 장단점 (0) | 2013.03.05 |
플랜지 레이팅 계산기 - Flange Rating Calculator (NPS 0.5 to 60) (0) | 2013.02.26 |
개스킷 재질 (Gasket Materials) (0) | 2013.02.26 |
볼 밸브냐? 게이트 밸브냐? 그것이 문제로다. (0) | 2013.01.30 |
파이프 재질 별 특징
|
|
재질 | 장점 | 단점 |
Carbon Steel | 저렴, 제작이 용이, 흔하고 가장 널리 쓰이는 재질. 염기성 환경에 저항성 | 산성 및 강염기에 매우 약함. 다른재질에 비해 잘 부러짐, 특히 저온에서는 취약함. |
Stainless Steel 스테인리스스틸 | 상대적으로 저렴, 제작이 용이. 카본스틸보다는 더욱 광범위한 환경에 저항을 가지며 다양한 종류가 있음. | 염소에 저항성이 없으며, 온도가 높아짐에 따라 저항력이 크게 떨어진다. |
254 SMO (Avesta) | 가격은 중간. 제작은 용이한 편. 스테인리스스틸과 비교해서 좀더 광범위한 온도와 농도 조건에서 저항력이 좋음. | 염소에 저항력이 거의 없으나 고온에서의 저항력은 개선이 가능하다. |
Titanium | 염소에 대한 저항력이 매우 좋음.(해수용으로 광범위 하게 이용됨). 비교적 얇은 두께에서 가공이 가능 | 재질이 크게 비싸지는 않으나 가공이 어려움. 많은 비용이 용접에서 발생. |
Pd stabilized Titanium | 염소에 대한 저항이 고온에서도 우수함. 티타늄의 저항력으로도 부족한 경우에 해수용으로 종종 사용됨. | 매우 비싼 재질인 동시에 가공도 어려우며 비용이 많이 든다. |
Nickel 니켈 | 고온의 부식성 유체에 우수한 저항력을 가진다. | 비용이 보통과 비쌈 사이이다. 용접이 어렵다. |
Hastelloy Alloy | 선택할 수 있는 폭이 굉장히 넓다. 다른 재질로는 불가능한 산성 물질도 커버할 수 있도록 특별히 제작되기도 한다. | 꽤 비싼 합급으로 꼭 필요한 곳에만 쓰는 것이 좋다. 대부분 용접은 쉬운 편이다. |
Graphite | 약한 염화수소 유체를 견뎌내는 몇 안되는 재질이다. | 깨지기 쉽고, 매우 비싸며, 가공도 어렵다. 특정타입의 흑연재질에서는 일부 물질이 확산되는 것으로 알려져있다. |
Tantalum | 다른 물질로는 견디기 어려운 매우 극한의 물질을 다룰 수 있다. | 초 고가이며, 절대적으로 필요한 곳에만 사용해야한다. |
-불펌금지-
<원문>
Material | Advantage | Disadvantage |
Carbon Steel | Low cost, easy to fabricate, abundant, most common material. Resists most alkaline environments well. | Very poor resistance to acids and stronger alkaline streams. More brittle than other materials, especially at low temperatures. |
Stainless Steel | Relatively low cost, still easy to fabricate. Resist a wider variety of environments than carbon steel. Available is many different types. | No resistance to chlorides, and resistance decreases significantly at higher temperatures. |
254 SMO (Avesta) | Moderate cost, still easy to fabricate. Resistance is better over a wider range of concentrations and temperatures compared to stainless steel. | Little resistance to chlorides, and resistance at higher temperatures could be improved. |
Titanium | Very good resistance to chlorides (widely used in seawater applications). Strength allows it to be fabricated at smaller thicknesses. | While the material is moderately expensive, fabrication is difficult. Much of cost will be in welding labor. |
Pd stabilized Titanium | Superior resistance to chlorides, even at higher temperatures. Is often used on sea water application where Titanium's resistance may not be acceptable. | Very expensive material and fabrication is again difficult and expensive. |
Nickel | Very good resistance to high temperature caustic streams. | Moderate to high expense. Difficult to weld. |
Hastelloy Alloy | Very wide range to choose from. Some have been specifically developed for acid services where other materials have failed. | Fairly expensive alloys. Their use must be justified. Most are easy to weld. |
Graphite | One of the few materials capable of withstanding weak HCl streams. | Brittle, very expensive, and very difficult to fabricate. Some stream components have been know to diffusion through some types of graphites. |
Tantalum | Superior resistance to very harsh services where no other material is acceptable. | Extremely expensive, must be absolutely necessary. |
'Design' 카테고리의 다른 글
전기 약어 (0) | 2013.03.12 |
---|---|
FEED (0) | 2013.02.25 |
PIPING & FITTING DIMENSIONS (0) | 2012.01.13 |
Hot tapping (0) | 2012.01.13 |
도면의 종류 (0) | 2012.01.13 |